Fall Tool Reset
Wednesday, September 8, 2021
When Adrienne and I first met there was a bit of an old man in me that would sharpen and clean the tools for the year. There's something peaceful about hand sharpening a blade, with an IPA within reach. Time slows down for me. Feedingt the kids curiosity of the role of the metal file to the mower blade. Removing sap. Finishing every tool with a light coat of recycle motor oil. There's something ritualistic about the whole thing and I'm enjoy it every year.
Wash Away Soil
Use the blast from the garden hose to remove soil. Scrape away any stuck-on mud with a putty knife or plastic scraper.Soak in Soapy Water
To help remove residual soil, fill a bucket with hot water and add about one-half teaspoon of dishwashing liquid per gallon of water. Add each tool after removing heavy soil and let them soak for 15-20 minutes.Rinse and Dry the Tools
Rinse every tool with cool water and dry.
Inspect for and Remove Rust
Check each tool for any sign of rust. If rust or pitting is present, Use a stiff wire brush or steel wool to scrub away rust spots. Lightly coat the tool with vegetable oil to aid in loosening the rust while you scrub.
Remove Gooey Sap
If the tools feel sticky, it could be plant sap or insect residue. Dip an old cloth in a bit of turpentine, lighter fluid, or Goo Gone. Wipe down the tool paying close attention to hinged areas.
Disinfect Tools
Before storing tools, they should be disinfected to kill bacteria and fungi that can cause problems. Mix a solution of two cups of chlorine bleach and one gallon of water in a bucket. Submerge the tools and let them soak for 10 minutes. Rinse well and dry completely with an old cloth.
Store Tools Correctly
Most gardening chores are seasonal but even if you know you're going to be using the shovel or trowel or shears the next day, don't leave them outside in the garden. After cleaning, return them to your storage area so they will remain dry and, hopefully, rust-free.
To keep small trowels and hand-tools rust-free and easy to find, fill a large flower pot or bucket with sand and add one cup of vegetable oil. Mix well and then insert the metal ends of the tools into the oiled sand.
If possible, hang larger tools from hooks or a pegboard to prevent warping of the handles and to keep metal components off the floor and dry.
Care for Wooden Handles
If your tools have wooden handles, the wood will eventually begin to dry out, split, and loosen from the metal component. Once or twice a year, sand the handles with medium-grit sandpaper to remove rough spots and rub them with linseed oil. The oil adds a protective barrier to help repel water.
Most wooden handles can be replaced by removing the metal component and installing a new handle.
Oil Moving Components
Any tool with a moving component like snips, shears, or pruners needs oil to keep moving parts working smoothly. This can be done by placing a drop or two of machine oil on the hinged parts.
It is also beneficial to take these tools apart once a year and rub down all of the components (screws and bolts) with machine oil. This helps remove any hard-to-see rust and mineral deposits.
Sharpen Blades and Edges
Any gardening tool with an edge—shovels, hoes, snips, pruners—will need to be sharpened occasionally. Large blades and edges can be sharpened with a 10-inch flat mill file and smaller, finer edges can be sharpened with a whetstone.
Begin by wiping down the blades with WD-40. File the edges at a 20 to 45-degree angle following the original bevel. Finish by wiping down with a soft cloth to remove any metal shavings.
Inspect for and Remove Rust
Check each tool for any sign of rust. If rust or pitting is present, Use a stiff wire brush or steel wool to scrub away rust spots. Lightly coat the tool with vegetable oil to aid in loosening the rust while you scrub.Remove Gooey Sap
If the tools feel sticky, it could be plant sap or insect residue. Dip an old cloth in a bit of turpentine, lighter fluid, or Goo Gone. Wipe down the tool paying close attention to hinged areas.Disinfect Tools
Before storing tools, they should be disinfected to kill bacteria and fungi that can cause problems. Mix a solution of two cups of chlorine bleach and one gallon of water in a bucket. Submerge the tools and let them soak for 10 minutes. Rinse well and dry completely with an old cloth.Store Tools Correctly
Most gardening chores are seasonal but even if you know you're going to be using the shovel or trowel or shears the next day, don't leave them outside in the garden. After cleaning, return them to your storage area so they will remain dry and, hopefully, rust-free.To keep small trowels and hand-tools rust-free and easy to find, fill a large flower pot or bucket with sand and add one cup of vegetable oil. Mix well and then insert the metal ends of the tools into the oiled sand.
If possible, hang larger tools from hooks or a pegboard to prevent warping of the handles and to keep metal components off the floor and dry.
Care for Wooden Handles
If your tools have wooden handles, the wood will eventually begin to dry out, split, and loosen from the metal component. Once or twice a year, sand the handles with medium-grit sandpaper to remove rough spots and rub them with linseed oil. The oil adds a protective barrier to help repel water.Most wooden handles can be replaced by removing the metal component and installing a new handle.
Oil Moving Components
Any tool with a moving component like snips, shears, or pruners needs oil to keep moving parts working smoothly. This can be done by placing a drop or two of machine oil on the hinged parts.It is also beneficial to take these tools apart once a year and rub down all of the components (screws and bolts) with machine oil. This helps remove any hard-to-see rust and mineral deposits.
Sharpen Blades and Edges
Any gardening tool with an edge—shovels, hoes, snips, pruners—will need to be sharpened occasionally. Large blades and edges can be sharpened with a 10-inch flat mill file and smaller, finer edges can be sharpened with a whetstone.Begin by wiping down the blades with WD-40. File the edges at a 20 to 45-degree angle following the original bevel. Finish by wiping down with a soft cloth to remove any metal shavings.
Tags
garden
Recipes
Creating a meal, creates conversations and brings people to together. Let us help you.
Get Recipes